ASTM D3654 PDF

We invite you to read our terms of use. Between laboratories Between testers Between rolls Residual 0. Take care in the choice of samples and when comparing results between fiberboard surfaces which may not be exactly the same. It is common to test at least? Standards Subsctiption may be the perfect astn.

Author:Shaktigul Gagore
Country:United Arab Emirates
Language:English (Spanish)
Genre:Health and Food
Published (Last):20 May 2016
Pages:284
PDF File Size:16.89 Mb
ePub File Size:1.76 Mb
ISBN:739-8-47741-970-9
Downloads:42280
Price:Free* [*Free Regsitration Required]
Uploader:Mulrajas



Tagis This standard is subject to revision at any time by the responsible technical committee and must be reviewed every? During storage, panels should be protected from damage or contamination. For Procedures F and G, substitute a? Standards Subsctiption may be the perfect solution. Originally approved in Take care in the choice of samples and when comparing results between fiberboard surfaces which may not be exactly the same.

We invite you to read our terms of use. The precision of tests conducted on nonstandard surfaces may be different than that described in Section Your comments are invited either for revision of this standard or for additional standards and should be addressed to ASTM International Headquarters. The assessment may be within a roll of tape, between rolls or production lots. This standard is not included in any packages. You may delete a document from your Alert Profile at any time.

Link to Active This link will always route to the current Active version of the standard. Standards Subscriptions from ANSI provides a money-saving, multi-user solution for accessing standards.

Your comments will receive careful consideration at a meeting of the responsible technical committee,1 which you may attend. ASTM International takes no position respecting the validity of any patent rights asserted in connection with any item mentioned in this standard. France Stock lots. Subscription pricing is determined by: The surface roughness height shall be 50 d 25 nm [2.

Test specimens should be taken from several rolls of a tape and, whenever possible, among several production runs of a tape.

Please first log in with a verified email before subscribing to alerts. This gives the test results for the roll of tape under consideration in the sampling plan. The surfaces of similar fiberboards may exhibit considerable variation between mills, between batches axtm one mill, and within batches.

Algomtl is the importers and exporters business partner. Already Subscribed to this document. If the document is revised or amended, you will be notified by email. Conduct an analysis of the logarithm of the data to determine the desired dd or comparative statistics. Special isothermal box for scooters and motorcycles. The panel is mounted vertically, a standard mass is asstm to the free end of the tape and the time to failure is determined.

No single value shall be considered as representative of the roll under test. Use of the Weibull distribution is an acceptable alternative. The components of the variance for the following factors were estimated: Procedure H may be used to compare the shear adhesion of tape applied to a standard steel surface and tested at an elevated temperature.

Wholesalers ads Partners Websites. Combining values from the two systems will result in non-conformance with the standard.

The adequate solution for the transport of your fresh products or frozen food or of your organic and Please first verify your email before subscribing to alerts. For procedures B, C, D, and G remove? One company reports that, with care, the between laboratory standard deviation and the residual including within roll standard deviation may be higher or lower than reported here, depending on the tape type and manufacturer.

We have no amendments or corrections for this standard. The use of an elevated temperature during test tends to reduce the duration of the test. Algomtl allows the purchase and v of lots from manufacturers, wholesalers and retailers. The edges for about mm [5 in. This may be used to compare the shear adhesion of a tape to a particular? This may or may not relate to the ability of d tape to adhere to other surfaces.

The surface shall be a true cylinder void of any convex or concave deviations. ASTM D Users of this standard are expressly advised that determination of the validity of any such patent rights, and the risk of infringement of such rights, are entirely their own responsibility. The 24 mm [1 in. International import and export trade leads board. Your Alert Profile lists the documents that will be monitored.

TOP Related Posts.

HEINEMANN PHYSICS 2AB PDF

ASTM D3654 PDF

.

DIAGRAPHIE SONIQUE PDF

Popular Publishers

.

Related Articles